it’s everyone’s worst nightmare – the check engine warning light illuminates on the dash. this common occurrence causes a sinking feeling in your gut and causes you to go into a deep panic mode.
before you go too deeply into that spiral, remember that some minor issues can cause your check engine light to come on. we look at the meaning of the check engine lights, the reasons it happens, and how to fix them.
check engine light meaning
the check engine light indicates there is something wrong with your engine’s electrical system. it can be due to a faulty engine sensor or any other damaged part in your engine. mostly it’s due to something wrong with the emissions control system.
in 1996, automakers began standardizing all systems with the obd-ii protocol. this system provides a list of diagnostic trouble codes that can be read through a universal connector.
the check engine light illuminates when the car’s computer recognizes a problem. it can be orange, amber, or yellow light, depending on the car manufacturer.
the check engine light can shine steadily, which indicates there’s an issue that must be checked out. these problems aren’t 2022世界杯榜 ly immediate concerns, but you should get right to the mechanic.
however, the check engine light that flashes off and on is indicating a critical fault. at this point, you should pull over and have the car towed.
some people confuse the check engine light with the service light. this important indicator has a wrench-like shape and says, “service now” or “service soon.” this light only serves a reminder to get your scheduled maintenance performed and doesn’t indicate an issue.
causes of check engine light
the most common cause of a check engine light is an issue with the emission control system like a bad oxygen sensor or maf sensor. it can also be due to issues with the ignition like bad spark plugs or ignition coils. basically, the check engine light can be caused by any issue with your engine.
because the check engine light is responsible for alerting you to any trouble, it can indicate small issues to major repairs. here are the five most common reasons this indicator turns on.
remember that a lot more things can cause the light to come on! check further down how to diagnose it properly!
1. loose gas cap
the car’s gas cap seals the fuel system, so the tank receives the right amount of pressure. when you don’t apply the gas cap tightly enough or it is damaged, the pressure could be off in the fuel system.
thankfully, this is one of the easiest fixes. you can either secure the gas cap or replace a damaged one for just a few dollars.
2. failing oxygen sensor
when an oxygen sensor begins to fail, you might also notice a decline in the fuel economy. many vehicles contain four oxygen sensors, and any of these can fail.
depending on the make and model of your vehicle, the oxygen sensor replacement cost could be around $250.
related: 5 symptoms of a bad oxygen sensor (o2)
3. failing catalytic converter
typically, the catalytic converter fails because you haven’t performed regular maintenance or you ignored other issues. if the spark plugs, wires or oxygen sensor require replacement, you should do it right away, or you could end up with this costly repair.
catalytic converter replacements cost $1,000 or more in most situations.
related: 8 symptoms of a bad catalytic converter
4. defective spark plugs or wires
when the spark plugs corrode or wear out, you will notice engine performance issues. it’s also possible that the engine won’t start at all. that’s because this critical part supplies the spark needed for ignition.
the spark plug wires are just as critical, supplying the spark created from the coil to the plugs where it can ignite the air-fuel mixture. both of these parts are replaced as part of a regular tune-up. check your owner’s manual to follow the manufacturer’s recommendations.
related: 6 symptoms of bad spark plugs
5. failing mass air flow sensor
the mass air flow sensor keeps track of how much air enters the engine. then, it uses these calculations to determine how much fuel needs to mix in.
when the maf sensor starts to go bad, you might notice a drop in fuel economy because the engine can’t run efficiently anymore. for most cars, the mass air flow sensor replacement is only between $100 and $400.
related: 8 symptoms of a bad maf sensor
how to fix check engine light
to fix a check engine light that is on, you will follow a few basic steps.
1. buy an obd reader
it isn’t expensive to buy your own obd code reader. with this handy tool, you can check common engine faults without paying a mechanic.
if you don’t want to buy an obd reader, you can check with your local parts store. many of the nationwide locations will check the codes for free.
2. scan for engine codes
under the driver’s side dashboard, you will see a trapezoid-shaped port. that’s where you want to plug in the code reader. make sure the engine and key are off when you plug it in.
however, once the scanner is hooked up and on, you want to turn the key to your vehicle on but leave the engine off. press the scan button and watch the codes that come up.
3. search the engine code
you can take your code to the internet to find the cause of your fault. at 2022世界杯非洲赛程表 , we keep our readers informed of the most common trouble codes.
if you can’t find the information you need online, consider calling your local dealership for help.
4. replace the defective part
once you know what the problem is, you can purchase the necessary replacement parts and install them. obviously, some of the repairs are going to cost a lot less than others, such as a replacement gas cap versus a catalytic converter.
however, you should never prolong a repair, as it could lead to more serious issues down the road.
5. erase the code
once everything is fixed, it’s time to erase the codes. plug your scanner back in and hold down the erase button.
you might need to confirm the changes. we recommend rescanning the engine to be sure they are gone. you will also see the check engine light go off.
if you are repairing an issue to pass a smog check, take your vehicle for a few drives before getting retested. many technicians can tell if you have recently deleted a code, so it’s best to drive for at least 50 miles first.
